Gap, roller gap, roller convexity
If two object edges are joined together, a gap always remains. If the gap has to satisfy technical or visual requirements, the course with respect to the size must be checked. If the gap should be measured completely, laser scanners in the scanCONTROL series are ideally suitable for this. Point laser sensors in the optoNCDT group are also used for precise gap measurement over a track.
Windscreen gap
The final appearance of a product plays a crucial role everywhere that panes are positioned automatically. Apart from the shape, stability, color etc., the final appearance is also dependent on the position ...
Show detailsCylinder breathing of the cylinder head gasket
Specially shaped eddy current sensors are integrated directly in the crankcase where they measure, for example, the expansion of the cylinder head gasket during the stroke. Pressures of up to 50 bar are ...
Show detailsSpecial roll gap measurement on calender press
For continuous, uniform material processing in the field of sealing technology, the gap between the rolls must be set with the hydraulic adjustment device and maintained constant. For this reason the top ...
Show detailsPistons
Combustion engines must withstand maximum loads during a long service life. In order to deal with this requirement, eddy current sensors from the eddyNCDT series are installed in the engine for many different ...
Show detailsPiston secondary movement
Among other things, the lateral movement of the piston in the cylinder is crucial for the service life of engines. Miniature eddy current sensors for this are integrated in the piston which measure onto ...
Show detailsSorting crabs
Crabs are sorted by size in a sorting system. Thereby, the crabs are transported using a vibrating unit on a roller which has a clearance between 20 mm and 40 mm. For checking the clearance, ...
Show detailsPiston – Top Dead Center
The Top Dead Center of the cylinder movement is measured for adjustment of the precise ignition point in engine development. In doing so, a miniature eddy current sensor is integrated in the cylinder head ...
Show detailsPiston Secondary Movement and Piston Ring Position
To improve the construction of internal combustion engines and damage analyzes, it is neccessary to measure the thermal and mechanical loads in the engine. Two important variables here are the transverse ...
Show detailsAir gap measurement in large electric motors
With very large electric motors (diameter larger than 10m) it is important for reasons of cost effectiveness and energy efficiency, to know the radial run out of the rotor from the stator inside the motor. ...
Show detailsInspecting gaps in car trims
In high quality vehicles, the trim typically consists not only of a single material (e.g. plastics) but many different bonded materials. This offers various design options but also many additional functions ...
Show detailsExact crusher gap adjustment in rotary crushers
Rotary crushers for quarries or ore mines can grind up to 3500 t of material to the desired grain size in one hour. For this purpose an eccentric bearing bush generates a rotary-oscillating movement of ...
Show detailsMeasuring the bearing gap in wind turbines
To date, bearing gaps were measured during standstill based on a tactile principle. Therefore, long inspection intervals were required, which in turn, may increase the risk of a complete plant failure. ...
Show detailsMeasuring the lubricating gap in plain bearings
The lubricating gap of a plain bearing is influenced by several factors such as temperature, speed, angle, load etc. This influence can only be measured under operating conditions. Therefore, a measurement ...
Show detailsEddy current sensors in tribology testers
Eddy current sensors from Micro-Epsilon are used for various measurement tasks in tribology testers of the ITR in Clausthal. They withstand the harshest ambient conditions there as they measure directly ...
Show detailsGap detection on glass
Glass substrates are required for certain medical tests. During manufacture of silicon chips, the substrate is milled in a defined grid with a depth of 800µm. For separation, the substrate is broken at ...
Show detailsClosed-loop gap control in magnetic bearings
A shaft weighing about 40kg is supported in magnetic bearings. A ferromagnetic shaft journal is suspended in a magnetic field which is excited by surrounding excitation coils. To regulate the gap ...
Show detailsGap measurement of tripping pins
When triggering a switching operation in test equipment for camshafts, a tripping pin is moved at high speed. A gap measurement detects whether the tripping pin has been completely extended and if ...
Show detailsMonitoring oil gaps in hydrostatic bearings
Hydrostatic bearings are used in large plant and machinery such as stone mills, telescopic installations etc. Monitoring the gap size is a critical factor, as any disturbances in the hydraulics can cause ...
Show detailsOil film thickness measurement in an internal combustion engine
Included in the objectives of current engine development are minimization of pollutants and the reduction of oil consumption. In order to be able to take measures in achieving these objectives, then along ...
Show detailsMeasuring glass cups
In the production of drinking glasses, the stem and cup are connected using a gas burner. In order to enable the precise connection of the glass stem and cup, the distance between stem and cup needs to ...
Show detailsDetection of turbocharger rotor dynamics
In order to inspect the behavior of turbochargers during different stress states, eddy current displacement sensors are applied in turbocharger test benches. The miniature design of the sensors and their ...
Show detailsLubrication gap
Sliding bearings are used for crankshaft bearings in the engine. A specific minimum distance is required so that the bearing operates as wear-free as possible. Miniature eddy current sensors are ...
Show detailsGap analysis in axial piston pumps
So far, gap measurements inside the pumps were not possible because of the extreme requirements. The sensors must be resistant to high speeds, high pressures up to 1,000 bar and temperatures above 100 ...
Show detailsRoller clearance
In rolling operations of metals, plastics or other materials, the distance between the two rollers to one another or between the roller and the bearing surface is the decisive measure. For sensitive processes and high material accuracies, it is important to constantly check the gap so that possible waste is avoided. For this purpose, inductive contacting or non-contacting methods are suitable.
Show detailsMonitoring mold deformations in aluminum die-casting
Monitoring tool deformation using inductive sensors based on eddy current enables high product quality combined with improved tool life and reduced rework. Usually, three to four eddyNCDT 3005 eddy current systems are used to ensure consistent gap monitoring.
Show details